Hyundai Translead’s best selling trailer, the HT HY-Cube®, offers a greater interior width for increased load capacity plus double decking capabilities. The snap-in plastic liners are made of recycled materials and are strong and easy to repair. A 101" lining-to-lining width offers up to 4.050 cubic feet of interior volume.
|Length||Exterior: 53' 0"
Interior: 52' 6"
Interior: 101" lining to lining
|Height||Exterior: 13' 6"
4050 cu. ft. of interior volume
|Tare Weight||14,200 lbs|
|Side Sheets||Side sheets 0.050" thick pre-painted white aluminum.|
|Side Posts||Slotted "A" logistic galvanized steel posts on 16" centers, 0.45" deep × 6.57" wide, with posts on 12" centers over coupler and landing gear areas.|
|Roof||One piece, 0.040" thick, full width aluminum sheet, tension leveled prior to installation.|
|Roof Bows||Galvanized steel anti-snag bows on 24" centers. Pre-bonded to roof sheet. Roof bows installed using four solid rivets, two per end.|
|Front Wall||Four hi-tensile, hat shaped posts securely fastened with 6 heavy-duty fasteners and reinforced with a special angle clip, welded to the upper coupler and covered with 0.050 aluminum front sheets.|
|Rear Frame||Hot-dipped 3/16" thick galvanized steel construction with low profile header, tube shaped posts. Forged steel angle iron in top corners for added rack resistance. Lights recessed in rear sill with heavy-duty protection bars.|
|Rear Doors||Composite construction of 1/2" composite panel covered by .019" thick pre-painted white galvanized inner and outer skins. Dual durometer seals bonded to door. Four hinges and one anti-rack locking bar with nylon bushings per door. Lock handles fitted with rubber grips for operator comfort and safety.|
|Interior Lining||White 0.235" thick HDPE lining installed full height between uprights with no fasteners. Side lining hooks into place for easy replacement. Exterior grade 0.50" plywood installed on bottom and 0.25" plywood installed on top over front wall.|
|Crossmembers||Four inch deep, hot rolled steel I-beam, 80,000 psi yield strength, located on 12" centers. Hat shaped crossmembers ahead of landing gear. Rear 4' of trailer has crossmembers located on 8" centers.|
|Upper Coupler||A.A.R. rated king pin, 3.40" deep.|
|Floor||Laminated Oak 1-3/8" nominal thickness with three screws per floorboard. With a 0.125" thick steel × 12" deep diamond plate threshold plate.|
|Landing Gear||Hot-dip galvanized wing plate and support gear bracing mounted to five crossmembers. Two speed, 50,000 lb. capacity, A.A.R. rated, with 10" × 10" sandshoes. Roadside crank handle.|
|Rear Underride Guard||Constructed per CMVSS 223 Regulations. Hot-dip galvanized underride guard. Bolt-on type with special 4" square Guard tube with end cap to prevent slippage and recessed for conspicuity tape.|
|Suspension||Hedrickson Vantraxx HKANT40K Air Ride|
|Hub & Drums||Ten stud, hub piloted with outboard mounted cast brake drums.|
|Wheels||Pre-painted white 8.25 × 22.5 steel disc.|
|Tires||Low profile 22.5 radial tires.|
|Axles||Five inch round, 22,500 lb. rating, 77.5" track.|
|Brakes||Non-asbestos lining 16.5" × 7" quick change type, "S" cam operated automatic slack adjuster.|
|ABS System||Two sensor, one modulator valve (2S/1M) system, PLC4Trucks compatible system.|
|Oil Seals||Stemco Platinum Performance.|
|Lights & Wiring||Color coded 12-volt sealed wiring system, internal ground, and special watertight molded connectors to accept sealed lamps.|
|PAINT & FINISH|
|Paint||Steel front impact guard is abrasive blasted, coated with zinc rich epoxy primer andwhite finish top coat|
|Undercoating||Flooring is pre-undercoated and crossmembers are dipped in a black color coating prior to installation. Landing gear and running gear areas painted with gray color non-hardening rust preventative.|
|Decals||D.O.T. approved Hyundai Translead logo conspicuity tape and FHWA inspection sticker.|
|Miscellaneous||Truck-Lite P/N 97960 registration cardholder on frontwall. White mud flaps with Hyundai logo mounted on rear of slider subframe.|
|Warranty||Limited five year warranty.|
Hyundai Translead can configure the rear of your trailer to meet your specific operational needs. From Pintle hook and side steps to additional tail lights we can build what you need.
Hyundai Translead offers aerodynamic components from various manufacturers to meet US EPA SmartWay and California Air Resource Board requirements.
Roll Up Doors available from various manufacturers.
Lift gates can be factory installed so that your trailer is ready for use when you need it.
To assist in achieving greater fuel savings, PSI systems can be installed at the factory.
Kemlite® ETR roof skins are available offering greater interior visibility and safety for both workers and cargo.
For increased interior visibility dome lamps are available from various manufacturers.
Wide based tires from various manufacturers are available to meet both EPA SmartWay and California Air Resources Board requirements.
Tri-Axle configurations available for those operations running heavy freight loads.